Search

DEALER LOGIN

1300 498 819

DEALER LOGIN

ABOUT US

CONTACT US

Search
Menu

IN HOUSE REPAIR

USER GUIDES/INFO

TRADE REGISTRATION

Return to previous page

Balboa

Balboa

Fault Codes

Pressure Switch Model Controllers (No M7 Sensor)
Code Fault
   
PD Power Down, On battery backup
OH Overheat
Flo/FL Flow Problem
Cool Spa is 11 degrees below the set temperature
ICE/IC Possible freeze condition
SN1/SN Hi-Limit fault
SN3/SN Temperature sensor fault
ILOC Interlock fault
EC/ECON Spa is in Economy Mode
STD/ST Spa is in Standard Mode
SL/SLP Spa is in Sleep Mode
   
   
Flashing LED Message  
Code Fault
   
1 Flash      Every 3 Seconds Hi-Limit Fault
2 Flashes Every 3 Seconds Pressure Switch Closed (FLC)
3 Flashes Every 3 Seconds Pressure Switch Open   (FLO)
4 Flashes Every 3 Seconds Temperature Sensor Fault
Flash (1 Sec On, 1 Sec Off Hi-Limit (OH)
Flash (Briefly off every sec) Sensor Fault
Flash (Briefly on every sec) Pressure Switch Fault
   
With M7 sensors  (Sensor on either side of heater)
Code Fault
   
– – -, – – Temperature not available (Economy mode or sleep mode)
– -F, – -C or – – Temperature not available (Priming)
CFE, CONFIG Configuration error (Dip switch settings)
CrC, CHKSUM Failed the program checksum test (Firmware installation)
dr / Heater may be dry will retest shortly Possible dry heater
drn, DRAINING Pump 1 is on while draining
drY, dy, Heater dry service reqd Verified dry heater
Ecn, Ec Spa is in economy mode
gFI, GFCI Spa could not trip the RCD
HFL, HL HTR Flow low Low Flow (Large difference between sensors)
Hot, Hot-Call SVC Extreme overheat (Pump may be stuck on)
ICE, IC, Freeze COND Potential freeze conditions (Pumps run)
LF, Low Flow Verified there is low flow
OHH, HH, HTR Temp LMT Service Reqd Heater has overheated
OHS, OH, SPA Temp LMT Spa has overheated
PHH, PH is High lower PH pH Level is high
PHL, PH is low raise PH pH Level is Low
Pr, Priming mode takes 4 Min The spa is operation in priming mode
PSt, Persist fail The Persistent memory cannot be read
Rt9, Test GFC Reminder time to check the RCD
rCA, Change mineral cartridg Reminder time to change the Nature 2 cartridge
rCH, New filter Reminder time to change the filters
rCL, Clean filter Reminder time to clean the filters
rCO, Clean cover Reminder time to clean the spa Cover
rdr, Drain water Reminder time to drain water
rPH, Check PH Reminder time to check pH levels (Adjust)
rSA, CK Sanitizer Reminder time to check sanitizer levels (Adjust)
rtC, RTC Failure Real time clock cannot be read
rtr, Treat Wood Reminder time to treat wood
SAH, Sanitizer High Sanitizer level is high
SAL, Sanitizer Low Sanitizer level is Low
SbY, Standby Mode Spa is in standby mode
SE, Standard economy Spa is in standard economy mode
SF, Safety Fault There is a suction block (Pipe block)
SLP, SL Spa is in Sleep mode
SnA, SA, Sensor A service Reqd Sensor A is not operating correctly
Snb, Sb, Sensor B service Reqd Sensor B is not operating correctly
SnS, Sn Sensors are out of balance
Std, St, Standard Spa is in Standard mode
StU, Stuck on Pump appears to be stuck on